Two are better than one Multi-GNSS will open up PPP to a much wider range of applications. By Francesco Basile, Terry Moore, Chris Hill, Gary McGraw and Andrew Johnson INNOVATION INSIGHTS by Richard Langley ARE WE THERE? In a multi-GNSS world, that is. We’ve asked that question from time to time in this column over the years. So, are we there yet? That depends. One definition of “multi” is more than one. In this sense, we were in a multi-GNSS world as long ago as 1996. In that year, we had two fully populated constellations of satellites: GPS and GLONASS. Unfortunately, the full GLONASS constellation was short-lived. Russia’s economic difficulties following the dissolution of the Soviet Union hurt GLONASS, and by 2002 the constellation had dropped to as few as seven satellites. But GLONASS was reborn, and by Dec. 8, 2011, a full 24-satellite constellation was again operational. But another meaning of “multi” is many, implying more than two. In the late 1990s, the first satellites to host transponders for satellite-based augmentation systems were launched. So, by the mid-2000s, even though GLONASS was still undergoing its rejuvenation, we were already in a three-constellation world. And receivers then on the market provided the necessary raw measurement data to yield positioning solutions from this system of systems with potentially more continuity and greater accuracy than those obtained using GPS alone. And so in July 2008, we featured the article “The Future is Now: GPS + GLONASS + SBAS = GNSS.” And then in June 2010, we had “GPS, GLONASS, and More: Multiple Constellation Processing in the International GNSS Service.” In the introduction to that article, we asked that same question: Are we there yet? We concluded that, for early adopters of GPS plus GLONASS data and products, we were. With Galileo test satellites in orbit and an early version of the BeiDou system operational, it was already clear that by the end of the current decade, it wouldn’t just be the early adopters who would be benefiting from multi-GNSS but virtually all users of satellite-based positioning and navigation. Although we aren’t quite there with fully operational Galileo and BeiDou constellations, we are getting pretty close. And so researchers are looking hard at how to make the best use of multiple-constellation observations in a variety of positioning and navigation scenarios. In this month’s column, a team of such researchers examines the potential benefit of combining GPS and Galileo observations for improving precise point positioning in urban environments, following the advice we read in the Book of Ecclesiastes: “Two are better than one.” Over the years, precise point positioning (PPP) has been applied to many real-time applications that require sub-decimeter-level accuracy over a wide area or on a global scale. It is currently a standard in scenarios characterized by open-sky conditions, where a receiver is likely to have continuous track of GNSS satellites. On the other hand, PPP’s typically long convergence time means the technique has not been widely used in constrained and transient signal environments associated with urban areas. Analysis with both simulated and real data has shown that, once Galileo reaches final operational status, the PPP convergence time will be cut by more than half when using both GPS and Galileo observations. Accordingly, multi-GNSS will open up PPP to a much wider range of applications. To begin, we assessed the positioning performance of GPS and Galileo signals, alone or used together, in open-sky conditions. A Simulink-based software simulator was used to simulate 24-hour-long observation sessions from 10 static (fixed location) receivers spread worldwide, which were then processed with the POINT software (developed by the University of Nottingham and three other British universities) in static (receiver assumed fixed) PPP mode with an elevation cutoff angle of 10° and with carrier-phase ambiguities estimated as real or floating-point values. For each station, the simulator was run 55 times to provide a sufficient number of data points to characterize the general behavior of the processing algorithms; therefore, a total of 550 points were considered. For better GPS-Galileo interoperability, PPP results based on the ionosphere-free (IF) combination between GPS L1 and L5 and Galileo E1 and E5a observables were considered. The metrics used to define the positioning performance are the errors in the north, east and down components of the position once all of a daily file has been processed and the time these errors take to converge below 10 centimeters. The open-sky condition always guarantees excellent geometry and signal continuity even considering only one constellation. PPP Results. TABLE 1 shows the root mean square (RMS) of the errors and convergence times of the three components of position for the different configurations for the 550 points considered. Both single- and dual-constellation systems are able to provide a sub-decimeter-level accuracy after a few tens of minutes. On average, positioning with Galileo E1-E5a IF performs better that GPS L1-L5 IF: the Galileo solution is more accurate and converges faster than the GPS solution. TABLE 1. Comparison between GPS-only, Galileo-only and GPS plus Galileo PPP results. RMS of the positioning errors and convergence times for the stations considered. The reason for this behavior is the assumed lower noise on Galileo pseudoranges. It is well known that the quality of the pseudoranges affects the convergence time of the PPP solution. For this reason, one would expect some improvements by employing the Galileo Alternative BOC (AltBOC) modulated E5 signal. Thanks to its very large signal bandwidth of at least 51 MHz, Galileo E5 is characterized by excellent rejection properties of both long-range and short-range multipath. However, as shown in Table 1, when comparing the PPP solutions obtained using the Galileo E1-E5 IF and E1-E5a IF combinations, they have nearly the same performance. The reason for this apparent contradiction can be found in the use of the IF combination with E1. Given that E1 represents the dominant source of error in the IF combinations, its noise is amplified by a factor of 2.34 in the IF combination with E5 and by a factor of 2.26 when combined with E5a. Also, the smaller errors (with respect to E1) in E5a are amplified by 1.26, while the one in E5 is amplified by 1.34. Therefore, depending on the noise level in the Galileo pseudoranges, there might be instances where the noise in the E1-E5 IF combination is close to the one in the E1-E5a IF combination. The number and the geometry of the observed satellites also affect the convergence time. For this reason, when using the two systems together, the time the vertical errors take to go below 10 centimeters was reduced by 50 percent with respect to the GPS-only case and by 18 percent with respect to the Galileo-only case. URBAN ENVIRONMENTS The poor signal visibility and continuity associated with urban environments, together with the slow (re)convergence time of PPP, usually make the technique unsuitable for land navigation in cities. However, as demonstrated in the previous section, using a dual-constellation not only improves the visibility conditions, but also reduces the PPP convergence time. Therefore, it might be possible to extend the applicability of PPP to land navigation in certain urban areas. To assess the positioning performance of two-constellation GNSS in these constrained environments, we analyzed the signal availability and geometry of five different simulated sites in the neighborhood of the University College London (UCL) campus. We adopted building boundaries, which determine the minimum elevation angles above which GNSS signals can be received due to building obstruction. FIGURES 1 and 2 illustrate the location and the building boundaries for each site. FIGURE 3 shows the junction (site B) between Gower Street (site A) and University Street (site C). FIGURE 1. Locations of the urban sites that are considered in the analysis. FIGURE 2. Building obstruction masks controlling satellite visibility for each site. FIGURE 3. Google Map image showing the junction (site B) between Gower Street (site A) and University Street (site C) in the midst of the University College London main campus. When processing data from multi-constellation GNSS, the differences between the system time of the different constellations need to be considered. For this reason, when GPS and Galileo are used simultaneously for precise positioning, the Kalman filter state vector (in general) includes the three position components, the receiver clock offset, and the GPS-Galileo Time Offset (GGTO) — whether or not a predicted value might be available in a navigation message from one of the constellations. On the other hand, in PPP processing, the multi-constellation precise products used are based on the same system time, and therefore, in theory, it is not necessary to estimate the GGTO. However, existing intersystem biases may affect the PPP performance, and so it is advisable to estimate them in the Kalman filter. Traditionally in PPP, the state vector also includes the residual zenith wet tropospheric delay and the carrier-phase ambiguities. Therefore, the minimum number of satellites required for GPS plus Galileo PPP is six. The geometry conditions are also an important factor for assessing the GNSS positioning performance. For land navigation, the horizontal dilution of precision (HDOP), which provides information about the achievable horizontal precision (and, assuming a bias-free solution, accuracy), is particularly relevant. For many land applications, such as precision agriculture and urban positioning, horizontal accuracy is more critical than vertical accuracy. Assuming that the ranging error in the carrier phase is 20 centimeters, to have decimeter-level horizontal accuracy HDOP needs to be no larger than 5. In most cases, HDOP values as small as 2 are desired. TABLE 2 gives an overview of the visibility and geometry conditions at the selected sites. A dual-constellation (GPS and Galileo) receiver placed at one of the two road junctions will always, or almost always, see at least six satellites with an HDOP better than 5. At sites A and C, these minimum requirements for signal availability and geometry are met for more than 75 percent of the day. Obstructions due to high buildings, such as at site E, allows us to have at least six satellites for only 13 percent of the time. TABLE 2. Percentage of epochs in 24 hours for which dual-constellation GNSS meets the minimum visibility (number of satellites, N) and geometry requirements (horizontal dilution of precision, HDOP). From our preliminary study, it seems clear that high-accuracy positioning in urban environments is possible, but only in some areas where buildings are relatively short, providing good signal availability and geometry. Things can slightly improve by considering additional systems, such as GLONASS and BeiDou, and by exploiting the non-line-of-sight (reflected) signals. However, it is well known that an additional obstacle for PPP in urban environments is signal discontinuity. Indeed, when a GNSS receiver loses lock on the carrier, the positioning filter needs to be reinitialized, meaning that further tens of minutes are required before reconvergence. To test the reconvergence time of PPP in transient signal environments, a pedestrian carrying a multi-GNSS receiver was simulated to be walking along the path in FIGURE 4. The receiver was simulated to be located for the first half hour of the simulation in the front yard of UCL’s Wilkins Building (where the simulation begins and ends), before starting to move. This is to allow the initial convergence of the PPP filter. FIGURE 4. The measured trajectory of the simulated pedestrian kinematic test. FIGURE 5 shows the visibility for a given GNSS satellite. Only the epochs when the receiver is moving are considered. Therefore, the first 30 minutes, when the receiver is static, are not included in the plot. Data gaps due to building obstructions are visible, with the largest being about 12 minutes and the average less than 2 minutes. As a consequence, the carrier-phase ambiguities need to be estimated all over again; and, as previously mentioned, this process usually requires tens of minutes before reconvergence. FIGURE 5. Satellite availability during the kinematic test. FIGURE 6 shows the HDOP and the number of visible satellites for the kinematic test, while FIGURE 7 shows the RMS, over 50 simulations, of the horizontal components of the positioning error when GPS L1 and L2 and Galileo E1 and E5, linearly combined into the IF combination, are processed in kinematic PPP mode with the POINT software. At the beginning of the kinematic test, when the HDOP is well below 5, the horizontal error is at the centimeter level, while, after 33 minutes from the beginning of the simulation, building obstructions don’t permit a converged solution below the 20-centimeter accuracy level. FIGURE 6. Horizontal dilution of precision and number of visible satellites for the kinematic test. FIGURE 7. RMS of the position errors for the kinematic test. This short example clearly demonstrates that two-constellation PPP has, in theory, the potential to precisely navigate ground vehicles in some urban environments; however, it is too sensitive to signal discontinuity. Slow solution reconvergence to the few decimeter/centimeter level still represents the main limitation to the use of PPP for high-accuracy applications in cities. Nonetheless, GPS plus Galileo PPP easily enables sub-meter-level horizontal accuracy for most of the simulations we have carried out. After signal loss, it only took a few tens of seconds to have a horizontal accuracy of better than a meter. SMOOTHED CORRECTIONS As an alternative to ambiguity-fixing methods aimed to improve the (re)convergence time, we propose a method that mitigates the effect of the ionosphere and which thereby reduces the reconvergence time of the PPP solution after initial convergence has been achieved. In this new approach, while the two-frequency carrier phases are linearly combined in the traditional IF combination, the uncombined pseudoranges are corrected by a pre-smoothed ionospheric delay (via a Hatch filter), computed using the geometry-free combination of two-frequency pseudoranges. Once the Hatch filter has converged, ideally we have IF pseudoranges with lower noise than the traditional ones. Therefore, in case the PPP filter needs to restart, we can obtain a quicker reconvergence thanks to the lower noise on the ionosphere-corrected pseudoranges. Indeed, provided that the signal gap is not very large, the ionosphere smoothing filter doesn’t need to be restarted from the raw values. It is possible to predict the ionospheric delay computed from two-frequency carrier-phase measurements using a linear fitting model from previous measurements within a sliding time window. As an example, high-rate data recorded on July 25, 2017, from station DAEJ in Daejeon, Republic of Korea, were used to analyze the ionosphere prediction error. In FIGURES 8 and 9, the RMS of the prediction errors for different time windows have been plotted against the data gap length. The prediction error depends on both the time latency of the observation and the elevation angle of the satellite. It increases with the data gap length, but larger time windows can damp the divergence of the error. A time window of 120 seconds was used both for satellites above and below 30° elevation angle. In this case, the error for a 5-minute prediction is about 4 centimeters for a satellite above 30° and 7 centimeters for satellites with a low elevation angle. These values are much smaller than the noise in the pseudorange measurements and can, therefore, be neglected. FIGURE 8. RMS of the prediction errors vs. data gap length for satellite elevation angles greater than 30°. FIGURE 9. RMS of the prediction errors vs. data gap length for satellite elevation angles less than than 30°. Multi-Frequency Combinations. The method introduced in the previous section allows users to be free from the constraint of IF observables and, therefore, to look for multi-frequency combinations aimed to minimize the noise on the pseudoranges. The next-generation GNSS satellites will broadcast open signals over three frequencies. The triple-frequency, geometry-preserving combination aimed to reduce the noise, instead of mitigating the ionosphere, can be used for positioning purposes. TABLE 3 summarizes the assumed values for the ratios ni between the noise on different GPS and Galileo pseudoranges and the ones on L1/ E1. FIGURE 10 shows a color map of the noise amplification factor associated with different linear combinations between GPS L1, L2 and L5. The x-axis is α3, the coefficient multiplying the pseudorange on L5 in the combination, while the y-axis is the ionosphere amplification factor of the triple-frequency combination with respect to L1, q. The noise for this combination can be as little as 0.57 times the noise on L1, while the corresponding ionosphere amplification factor is 1.49. Once the smoothed ionosphere correction has converged, we can potentially have an IF pseudorange 81 percent less noisy than the L1-L2 IF, and, therefore, a much faster reconvergence. TABLE 3. Assumed noise, ni, on GPS and Galileo pseudoranges, i, and their ionospheric delay, q, with respect to L1/ E1. FIGURE 10. Geometry-preserving surface in the space q-α3-n (ionosphere amplification factor – L5 pseudorange multiplier – noise amplification factor) for GPS L1-L2-L5 combinations. Similar conclusions can be drawn by considering Galileo signals. Using triple-frequency combinations with E1, E5a and E5b, we can obtain 81 percent less noise than E1-E5a IF, while a reduction of the noise in the IF pseudorange up to 90 percent was observed using E5 alone. Triple-frequency combinations involving E5 don’t bring such large improvements with respect to using E5 alone. Indeed, a maximum of 16 percent less noise can be registered when combining E1, E5a and E5 with respect to the E5 uncombined case. TABLE 4 illustrates the minimum noise amplification factor for each triple-frequency combination and its ionosphere amplification factor. TABLE 4. Minimum noise achievable through GPS and Galileo triple-frequency pseudorange combinations and their ionospheric delay with respect to L1/ E1. The noise associated with the ionosphere-corrected multi-frequency pseudorange combination is as large as meter level before converging to centimeter level. For this reason, a proper weighting method, which considers the varying noise on the ionosphere correction, needs to be employed. To test the benefit of the new approach for the reconvergence time, three hours of simulated GPS and Galileo data from a static site in La Misere, Seychelles, were processed with the POINT software in kinematic mode. After 90 minutes, the PPP filter was forced to restart to simulate reconvergence. The multipath time constant was set to 5 seconds, which is a typical value for kinematic multipath. The performance of the traditional L1- L2 IF combination was compared with the triple-frequency pseudorange combination, corrected by the smoothed ionosphere delay coming from the Hatch filter. FIGURE 11 shows the precision (RMS error over 50 simulations) of the horizontal components after filter restart. The new approach has much faster reconvergence than the traditional PPP method based on the IF combination. Indeed, while the traditional method takes about 11 minutes to have a horizontal error below 10 centimeters, using the low-noise combination, this accuracy is achieved after 171 seconds. Even better performance can be achieved considering the Galileo E5 signal (see FIGURE 12). FIGURE 11. RMS error of the horizontal position components of static site using GPS data after filter restart. FIGURE 12. RMS error of the horizontal position components of static site using Galileo data after filter restart. The E1-E5 IF combination requires 10 minutes for the horizontal convergence, while using E5 with the Hatch filter we have the horizontal solution converged in about 30 seconds. It is worth noticing that in the presence of static multipath, the proposed weighting method may lead to an overly optimistic weighting of the pseudorange measurements in the PPP filter and to a slower reconvergence of the positioning solution. Indeed, the long correlation time in the static multipath, of the order of a few minutes, makes it hard to filter out by the Hatch filter, hence the corrected measurements have larger errors than expected. The effect of static multipath in the new configuration is visible in FIGURE 13, where the reconvergence of the horizontal component for the L1-L2 IF combination is compared with the new approach. In this case, the time constant of the simulated multipath was set to 1 minute. In this scenario, the triple-frequency low-noise combination corrected by the smoothed ionosphere combination quickly converges below 20 centimeters; however, it takes significantly longer than the L1-L2 IF combination to reach the 10-centimeter accuracy level. FIGURE 13. RMS error of horizontal position component of static site using GPS data after filter restart with 1-minute multipath time constant. Also, the new method was tested with the kinematic simulation as in the previous section. Here, the GPS triple-frequency combined pseudorange and Galileo E5 pseudorange (both corrected with the smoothed ionosphere) are processed in kinematic PPP mode with the POINT software. FIGURE 14 compares the RMS of the horizontal errors with the IF configuration. Less than a minute after the receiver lost lock on the satellites, the solution reconverged below the 20-centimeter level, while it took less than 30 seconds to go below 50 centimeters. FIGURE 14. RMS error of the horizontal position components of kinematic trajectory using GPS and Galileo data and the smoothed ionosphere approach after filter restart. CONCLUSIONS In this article, we described a comparison that we carried out between GPS-only, Galileo-only and GPS plus Galileo PPP. Results based on simulated open-sky conditions demonstrated that Galileo performs better than GPS thanks to an assumed lower E1-E5a IF noise with respect to L1-L5. Two-constellation PPP enables faster (re)convergence compared to the single constellation case. An analysis of GNSS signal availability, continuity and satellite geometry was also performed to study the feasibility of PPP in urban environments. Preliminary results, based on simulations, showed that dual-constellation (GPS plus Galileo) PPP is possible in urban areas with relatively short buildings in which a satellite minimum availability requirement is met most of the time. However, signal discontinuity still represents the major problem for traditional PPP in urban environments, due to long reconvergence times. Finally, we proposed a new PPP configuration based on triple-frequency combinations, intended to minimize the noise on the pseudorange and corrected by a smoothed ionospheric delay. This configuration seems to provide faster reconvergence than the traditional PPP with the IF combination if applied to kinematic scenarios. In static applications, the very slow varying multipath error makes the proposed weighting method, based on the error in the smoothed ionosphere correction, overly optimistic. In such cases, the IF combination reconverges more quickly to high-accuracy levels better than 20 centimeters. ACKNOWLEDGMENTS The research described in this article was sponsored through a studentship agreement between the University of Nottingham and Rockwell Collins UK Limited. The article is based on the paper “Multi-Frequency Precise Point Positioning Using GPS and Galileo Data with Smoothed Ionospheric Corrections” presented at the 2018 IEEE/ION Position, Location and Navigation Symposium, held in Monterey, California, April 23–26, 2018. All figures attributed to the authors unless otherwise specified. MANUFACTURERS The receiver at station DAEJ is a Trimble NetR9. FRANCESCO BASILE is a postgraduate research student at the Nottingham Geospatial Institute of the University of Nottingham in the United Kingdom. He received his M.Sc. in space and astronautic engineering from the University of Rome – La Sapienza and his B.Sc. in aerospace engineering from the University of Naples – Federico II, both in Italy. TERRY MOORE is the director of the Nottingham Geospatial Institute where he is the Professor of Satellite Navigation. He is a fellow and the president of the Royal Institute of Navigation (RIN) and also a fellow and a member of council of the Institute of Navigation (ION). CHRIS HILL is an associate professor in the Faculty of Engineering at the University of Nottingham and a member of the Nottingham Geospatial Institute research group. He holds a Ph.D. in satellite laser ranging and he is a fellow of the RIN. GARY MCGRAW is a technical fellow with the Rockwell Collins Advanced Technology Center in Cedar Rapids, Iowa. McGraw is a fellow of the ION and is a senior member of the IEEE. ANDREW JOHNSON is a chief engineer at Rockwell Collions UK in Winnersh, Berkshire, United Kingdom. Johnson has a B.Sc. in electronic and electrical engineering from the University of Surrey in Guildford, United Kingdom. FURTHER READING Authors’ Conference Paper “Multi-Frequency Precise Point Positioning Using GPS and Galileo Data with Smoothed Ionospheric Corrections” by F. Basile, T. Moore, C. Hill, G. McGraw and A. Johnson in Proceedings of PLANS 2018, the Institute of Electrical and Electronics Engineers / Institute of Navigation Position, Location and Navigation Symposium, Monterey, California, April 23–26, 2018, pp. 1388–1398, doi: 10.1109/PLANS.2018.8373531. Multi-Constellation Use in Built-up Areas “Making It Better: Low-Cost Single-Frequency Positioning in Urban Environments” by I. Smolyakov and R.B. Langley in GPS World, Vol. 29, No. 5, May 2018, pp. 42–48. “Quo Vademus: Future Automotive GNSS Positioning in Urban Scenarios” by M. Escher, M. Stanisak and U. Bestmann in GPS World, Vol. 27, No. 5, May 2016, pp. 46–52. “Multi-Constellation GNSS Performance Evaluation for Urban Canyons Using Large Virtual Reality City Models” by L. Wang, P.D. Groves and M.K. Ziebart in Journal of Navigation, Vol. 65, No. 3, July 2012, pp. 459–476, doi: 10.1017/S0373463312000082. “Potential Benefits of GPS/GLONASS/GALILEO Integration in an Urban Canyon – Hong Kong” by S. Ji, W. Chen, X. Ding, Y. Chen, C. Zhao and C. Hu in Journal of Navigation, Vol. 63, No. 4, October 2010, pp. 681–693, doi: 10.1017/S0373463310000081. Multi-Constellation Use in Aviation Applications “Assessment of Alternative Positioning Solution Architectures for Dual Frequency Multi-Constellation GNSS/SBAS” by G. McGraw, B.A. Schnaufer, P.Y. Hwang and M.J. Armatys in Proceedings of ION GNSS+ 2013, the 26th International Technical Meeting of the Satellite Division of The Institute of Navigation, Nashville, Tennessee, Sept. 16–20, 2013, pp. 223–232. Advances in Precise Point Positioning “More Is Better: Instantaneous Centimeter-Level Multi-Frequency Precise Point Positioning” by D. Laurichesse and S. Banville in GPS World, Vol. 29, No. 7, July 2018, pp. 42–47. “Where Are We Now, and Where Are We Going?: Examining Precise Point Positioning Now and in the Future” by S. Bisnath, J. Aggrey, G. Seepersad and M. Gill in GPS World, Vol. 29, No. 3, March 2018, pp. 41–48. “Undifferenced GPS Ambiguity Resolution Using the Decoupled Clock Model and Ambiguity Datum Fixing” by P. Collins, S. Bisnath, F. Lahaye, and P. Héroux in Navigation, Vol. 57, No. 2, Summer 2010, pp. 123–135, doi: 10.1002/j.2161-4296.2010.tb01772.x. “Integer Ambiguity Resolution on Undifferenced GPS Phase Measurements and Its Application to PPP and Satellite Precise Orbit Determination” by D. Laurichesse, F. Mercier, J.-P. Berthias, P. Broca and L. Cerri in Navigation, Vol. 56, No. 2, Summer 2009, pp. 135–149, doi: 10.1002/j.2161-4296.2009.tb01750.x. Hatch Filter “Combinations of Observations” by A. Hauschild, Chapter 20 in Springer Handbook of Global Navigation Satellite Systems, edited by P.J.G. Teunissen and O. Montenbruck, published by Springer International Publishing AG, Cham, Switzerland, 2017. “The Synergism of GPS Code and Carrier Measurements” by R. Hatch in Proceedings of the Third International Geodetic Symposium on Satellite Doppler Positioning, Las Cruces, New Mexico, Feb. 8–12, 1982, Vol. II, pp. 1213–1232. Dilution of Precision “Dilution of Precision” by R.B. Langley in GPS World, Vol. 10, No. 5, May 1999, pp. 52–59. Kalman Filtering “Least-Squares Estimation and Kalman Filtering” by S. Verhagen and P.J.G. Teunissen, Chapter 22 in Springer Handbook of Global Navigation Satellite Systems, edited by P.J.G. Teunissen and O. Montenbruck, published by Springer International Publishing AG, Cham, Switzerland, 2017. “The Kalman Filter: Navigation’s Integration Workhorse” by L.J. Levy in GPS World, Vol., No., September 1997, pp. 65–71.
china gps jammer rangeOem ad-0760dt ac adapter 7.5vdc 600ma used-(+)- 2.1x5.4x10mm,acbel api3ad03 ac adapter 19v dc 3.42a toshiba laptop power supp.t-n0-3300 ac adapter 7.6v dc 700ma power supply travel charger,the figure-2 depicts the out-band jamming signal with the carrier frequency of gps transmitter.black & decker s036c 5102293-10 ac adapter 5.5vac 130ma used 2.5,finecom a1184 ac adapter 16.5vdc 3.65a 5pin magsafe replacement,globtek gt-21089-1509-t3 ac adapter 9vdc 1.7a 15w used -(+)- 2.5,modul 66881f ac adapter 12vac 1660ma 25w 2p direct plug in power.dc90300a ac adapter dc 9v 300ma 6wclass 2 power transformer.high voltage generation by using cockcroft-walton multiplier,dp48d-2000500u ac adapter 20vdc 500ma used -(+)class 2 power s,3com 61-0107-000 ac adapter 48vdc 400ma ethernet ite power suppl.creative ud-1540 ac adapter dc 15v 4a ite power supplyconditio,ault a0377511 ac adapter 24v 16va direct plugin class2 trans pow,digipower 35d-7.5-400 ac dc adapter 7.5v 400ma power supply clas,“1” is added to the fault counter (red badge) on the hub icon in the ajax app,cisco at2014a-0901 ac adapter 13.8vdc 1.53a 6pins din used powe,ault t41-120750-a000g ac adapter 12vac 750ma used ~(~)2.5x5.5.80h00312-00 5vdc 2a usb pda cradle charger used -(+) cru6600,delta adp-90cd db ac adapter 19vdc 4.74a used -(+)- 2x5.5x11mm,all these security features rendered a car key so secure that a replacement could only be obtained from the vehicle manufacturer.braun 4728 base power charger used for personal plaque remover d,realistic 20-189a ac adapter 5.8vdc 85ma used +(-) 2x5.5mm batte,the operating range does not present the same problem as in high mountains,new bright a871200105 ac adapter 24vdc 200ma used 19.2v nicd bat,power supply unit was used to supply regulated and variable power to the circuitry during testing.dell adp-13cb ac adapter 5.4vdc 2410ma -(+)- 1.7x4mm 100-240vac.delta adp-40zb rev.b ac adapter 12vdc 3300ma used 4pin din,serene cl cordless ac adapter 7.5vdc 300ma used 2.5x5.5x9.8mm 90,the circuit shown here gives an early warning if the brake of the vehicle fails.
jammers orangeburg sc today 4963 3227 1871 750 6406 gps jammer technology pdf 8528 1696 3289 625 858 gps jammer military operation 2145 3229 5144 2151 948 gps jammer ebay app 7576 4432 7746 409 6162 gps jammer illegal logging 5885 4292 7578 1630 3175 gps,xmradio, jammer homemade 7399 2871 2510 4628 3929 gps jammer uk national 6919 5805 7141 6098 930 china drone jammer circuit 1261 8973 6327 5449 7466 phone jammer range funeral 7299 4127 7766 7139 2176 gps jammer detection company 2406 1673 2928 7393 3391 wifi gps jammer kit 2970 5589 6162 1436 1060 gps jammers wholesale from china kitchen 6429 7192 8576 8583 3813 mobile jammer frequency range 959 6835 766 4384 7337 jammers from china 706 3011 7326 562 6471 gps jammer long range 6304 4598 1084 5316 442
Eps f10652-a ac adapter 18-24vdc 3.61-2.70a used power supply,tc-60a ac adapter 9vdc 1.3a -(+) 1.3x3.5mm 100-240vac used direc.liteon pa-1900-08hn ac adapter 19vdc 4.74a 90w used.philips 4203-035-77410 ac adapter 2.3vdc 100ma used shaver class,kinetronics sc102ta2400f01 ac adapter 24vdc 0.75a used 6pin 9mm,i think you are familiar about jammer,lei mt20-21120-a01f ac adapter 12vdc 750ma new 2.1x5.5mm -(+)-,akii technology a10d2-09mp ac adapter +9vdc 1a 2.5 x 5.5 x 9.3mm,casio ad-5mu ac adapter 9vdc 850ma 1.4x5.5mm 90 +(-) used 100-12,dc1500150 ac adapter 15vdc 150ma used 1.8 x 5.5 x 11.8mm,ac adapter 6vdc 3.5a 11vdc 2.3a +(-)+ 2.5x5.5mm power supply,communication system technology use a technique known as frequency division duple xing (fdd) to serve users with a frequency pair that carries information at the uplink and downlink without interference,radioshack 15-1838 ac adapter dc 12v 100ma wallmount direct plug.trendnet tpe-111gi(a) used wifi poe e167928 100-240vac 0.3a 50/6,dell sa90ps0-00 ac adapter 19.5vdc 4.62a 90w used -(+) 5x7.3mm,compact dual frequency pifa …,acbel ap13ad03 ac adapter 19vdc 3.42a power supply laptop api-76.syquest ap07sq-us ac adapter 5v 0.7a 12v 0.3a used5 pin din co,nokia acp-7e ac adapter 3.7v 355ma 230vac chargecellphone 3220,phihong psm11r-120 ac adapter 12vdc 1.6a -(+) 2.1.x5.5mm 120vac.panasonic vsk0964 ac adapter 5vdc 1.6a used 1.5x4x9mm 90° round,qc pass e-10 car adapter charger 0.8x3.3mm used round barrel.jvc ap v14u ac adapter 11vdc 1a used flat proprietery pin digit.black & decker 371415-11 ac adapter 13vdc 260ma used -(+) 2x5.5m,altec lansing s024em0500260 ac adapter 5vdc 2.6a -(+) 2x5.5mm 26,so to avoid this a tripping mechanism is employed.databyte dv-9319b ac adapter 13.8vdc 1.7a 2pin phoenix power sup,bellsouth dv-9150ac ac adapter 9v 150ma used -(+)- 2x5.5x9.8mm.compaq pa-1440-2c ac adapter 18.85v 3.2a 44w laptop power supply.mbsc-dc 48v-2 ac adapter 59vdc 2.8a used -(+) power supply 100-1.
Bell phones dvr-1220-3512 12v 200ma -(+)- 2x5.5mm 120vac power s,dell adp-50sb ac adapter 19vdc 2.64a 2pin laptop power supply,a portable mobile phone jammer fits in your pocket and is handheld,liteon ppp009l ac adapter 18.5v dc 3.5a 65w laptop hp compaq,apple m4551 studio display 24v dc 1.875a 45w used power supply.mayday tech ppp014s replacement ac adapter 18.5v dc 4.9a used.retrak whafr24084001 ac adapter 19vdc 3.42a used 4.2x6mm power s,liteon pa-1650-02 ac adapter 19v dc 3.42a used 2x5.5x9.7mm,csec csd1300150u-31 ac adapter 13vdc 150ma used -(+)- 2x5.5mm.tenergy oh-1048a4001500u-t ac adapter 30vdc 1/1.5a used univers,creative ppi-0970-ul ac dc adapter 9v 700ma ite power supply.110 – 220 v ac / 5 v dcradius..